banner



Can I Use Old Wifi Router For Wifi Cameras

When your wireless settings or networking equipment change, the Wi-Fi cameras connected to the erstwhile network will disconnect from the internet. This is because they are still programmed with the old Wi-Fi information. Once the cameras have the new Wi-Fi information they can reconnect.

Note: If your cameras are connected to an Alarm.com Smart Gateway, they volition stay connected fifty-fifty if your network changes.

Prepare for a time to come network change

Let your service provider know that your networking equipment or wireless settings are going to alter. They can then be prepared to assist you reprogram your cameras after the change if necessary.

Depending on how comfortable you are with reprogramming your camera'southward wireless information, you can as well attempt to reprogram the camera yourself.

How to reprogram a disconnected photographic camera to a Wi-Fi network

The website and app accept built-in troubleshooting wizards that y'all tin can access to get personalized reconnection steps.

For general steps, there are three possible ways to reconnect a disconnected camera. Using WPS is the easiest method, just Access Indicate (AP) manner or Ethernet may as well exist an option if WPS does not work.

To reconnect a camera using WPS manner:

Use your router's WPS push to quickly reconnect your cameras to the network. WPS functions as a way for the router to share its Wi-Fi credentials with another device without the user having to enter the credentials. Both the router and the camera need to be in WPS way at the aforementioned fourth dimension for the camera to connect successfully.

Important : Some routers exercise not have WPS. If your router does non have a WPS push button, or if the button is disabled (i.e., if the LED for the WPS button blinks red or does not low-cal up when y'all printing it), try using Access Betoken (AP) style or Ethernet instead. For more details about whether WPS is available on your router, refer to the manufacturer's user manual.

  1. Press and agree the WPS push button on your router until the LED starts flashing. Typically this button is labeled with the letters WPS, two arrows forming a circle, or a lock icon.
  2. While the router's WPS push is flashing, press and hold the WPS/Reset push on the camera for 3 seconds. Release the push equally before long as the LED starts flashing blue. Caution: Holding theWPS/Reset button too long, over 6 seconds, could result in the camera resetting to its factory defaults. The photographic camera's LED will flash red and green to point information technology is resetting, later which the camera must be removed and re-enrolled on the account.
  3. Expect for the LED on the photographic camera to turn solid greenish. This can take upwardly to 5 minutes, and the camera might go through a few different LED patterns.
  4. One time the photographic camera's LED is solid green, verify you tin can see live video on the Customer Website or app.
To reconnect a camera using AP mode:

Utilize a Wi-Fi enabled device (i.eastward., a smartphone, tablet, or computer) to connect your cameras to the network. Access Betoken (AP) fashion functions past letting you connect to the camera direct and make changes to its Wi-Fi settings without the camera existence connected to the cyberspace.

  1. Press and hold the WPS/Reset push on the camera for 5 seconds. Release the button as soon as the LED starts flashing white. The photographic camera is now broadcasting its ain Wi-Fi network. Caution: Holding theWPS/Reset button too long, over 7 seconds, could event in the camera resetting to its factory defaults. The photographic camera'due south LED will wink ruddy and green to indicate it is resetting, afterwards which the camera must be removed and re-enrolled on the account.
  2. Apply a Wi-Fi enabled device (i.e., a smartphone, tablet, or computer) to connect to the Wi-Fi network named ALARM:20:XX:XX where XX:XX:Xx is the last six digits of the camera's MAC address.
  3. Open a spider web browser on the device and enter the camera'south Admission Point web accost (e.yard., http://v723install, http://522irinstall, etc.) or192.168.1.1 in the address bar and follow the onscreen instructions.
    1. Click Scan for wireless networks.
    2. Click to select your Wi-Fi network.
    3. In Security Fundamental, enter your Wi-Fi password.
    4. Click Save.
    5. ClickOkin the pop-up window that appears asking to refer to the website.
  4. One time the camera'due south LED is solid light-green, verify you tin come across live video on the Customer Website or app.
To reconnect a photographic camera using Ethernet:

Use an Ethernet (i.e., Cat5) cable to connect your photographic camera directly to the router, and so reprogram the camera'due south wireless settings using the website.

Annotation: Some cameras do not have an Ethernet port. If that is the example, try using WPS or AP to connect the cameras.

  1. Remove power from your camera.
  2. Adhere ane cease of an Ethernet cable to the photographic camera and the other terminate to your router.
  3. Power on your camera.
  4. Wait for the camera's status LED to plough solid dark-green. This can take up to 5 minutes.
  5. Configure your camera's Wi-Fi settings.
  6. Remove the Ethernet cable and power cycle (i.eastward., remove ability then reapply it) your camera.
  7. Once the camera'southward LED is solid greenish, verify y'all can meet live video on the Customer Website or app.
LED troubleshooting

Some troubleshooting steps vary betwixt the connectedness methods. Wait for the method (i.e. WPS mode, AP mode, or Ethernet) you lot are currently attempting to get accurate steps. If a method is not specified, it applies to all three.

LED color Function Troubleshooting
Green flashing.png The camera is able to speak to the router but does not have a full internet connection.
  1. If the LED is flashing green for more than than ii minutes, power the camera downward for a few seconds and then apply power.
  2. Allow the camera to boot up. If the LED is however flashing dark-green after a few minutes, remove power from the router for at least 1 minute, and restore power.
  3. Wait a few minutes for the net connexion to be re-established.
Red solid.png The camera is unable to connect to a wireless network. AP mode or Ethernet:
  1. Double-cheque the Wi-Fi password and verify that y'all are entering the correct one.
  2. Retry the same connection method.
  3. If another attempt is unsuccessful, effort a different method of reconnecting the camera.

WPS mode:

  1. verify that WPS is enabled in the router. The router manual should have information about WPS.
  2. Retry the aforementioned connectedness method.
  3. If another attempt is unsuccessful, try a different method of reconnecting the camera.

Notation : If the router is verified to take WPS enabled, it may indicate that the photographic camera is also far away for WPS to take effect.

Red and green flashing.png Ethernet: 
  • The password entered may be wrong

WPS or AP mode:

  • The video device is resetting (AP or WPS methods)
Ethernet:  

WPS or AP mode:

  • If the flashing starts after holding the WPS/Reset button on the video device, the video device is resetting. Contact your service provider for assistance.

Need more than help?

If you have tried multiple reconnection methods and the photographic camera is still non reconnecting, contact your service provider for further assist.

Was this commodity helpful?

3.7 out Of five Stars
v Stars 33%
four Stars 33%
3 Stars 0%
2 Stars 33%
one Stars 0%

How can we improve this article?

Source: https://help.myalarmcenter.com/knowledge/how-can-a-camera-be-reconnected-to-a-wi-fi-network-if-the-router-network-equipment-or-wireless-settings-change/

Posted by: pollardwhictibed.blogspot.com

0 Response to "Can I Use Old Wifi Router For Wifi Cameras"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel